Power analyzer showing power factor, THD and the current waveform of a power supply
Real power, apparent power, PF and harmonics on a power analyzer.
Posted in

How to Measure Power Factor Correctly (PF, THD, Harmonics)

A 100 W power supply can load the mains wiring like a 175 VA one. The ratio between the two is the power factor, and it is easy to measure wrongly: with two meters instead of a power analyzer, with cos φ instead of true PF, with an average-responding clamp meter, or over a scope window that is not a whole number of cycles. This guide shows engineers and technicians how to measure power factor correctly, including harmonics, THD and the IEC 61000-3-2 limits.

The illustrations in this guide are live: click the buttons under each one to change the load or the method and watch the numbers change.

1. What Is Power Factor?

PF = P / S with P = (1/T) ∫ v·i dt (W) and S = Vrms × Irms (VA)

Real power P is the average of the instantaneous product of voltage and current: the power that does work. Apparent power S is what the wiring, fuses, transformers and generators have to carry. A PF of 1 means every amp does useful work; a PF of 0.57 means the wiring carries 1.75 times the current a resistive load would need.

PF matters for wiring and breaker sizing, generator and UPS capacity, utility tariffs, and compliance: harmonic current limits (IEC 61000-3-2) and efficiency programs (for example, 80 PLUS certification requires a PF of at least 0.9 at full load).

2. Displacement vs Distortion

  • Displacement: the current is a sine wave, but shifted in time from the voltage (motors, transformers, capacitor banks). Measured by cos φ of the fundamental.
  • Distortion: the current is not a sine wave (capacitor-input rectifiers draw narrow peaks). Measured by the distortion factor DF = I1/Irms.

PF = cos φ × DF and, for a sinusoidal voltage, PF = cos φ / √(1 + THDi²)

Key point: cos φ is not the power factor. A rectifier without PFC has cos φ ≈ 1 but a PF of about 0.5 to 0.7.
Load:
Two line cycles. PF, cos φ, THD and crest factor are calculated live from the waveforms shown.
cos φ: Current THD:
The power components: real P, reactive Q (displacement) and distortion D add up to the apparent power S.

3. Equipment You Need

ItemWhy
Power analyzerMeasures W, VA, PF, cos φ and harmonics with true-RMS inputs, wide bandwidth and high crest factor. A good DMM pair or a scope is not a substitute for compliance work.
Stiff, low-distortion AC sourceVoltage distortion and source impedance change the current waveform and the PF. For harmonic testing, IEC 61000-3-2 sets requirements for the source voltage.
Current input or shuntThe analyzer’s direct current inputs, or a calibrated shunt or current sensor with enough bandwidth. Not an average-responding clamp meter.
Electronic loadTo step the DUT through its load points.
Safety: the analyzer’s inputs are at mains potential. Never float an oscilloscope by removing its earth; use rated differential probes.

4. Power Analyzer Settings

SettingUseWhy
SynchronizationVoltage channel, line frequencyThe analyzer must find the true cycle boundaries; syncing on peaky current can be unstable.
Averaging / updateWhole line cyclesPartial cycles bias P and the RMS values.
Current rangeCrest factor ≥ 3 at your peakRectifier current has a crest factor around 3 or more; clipped peaks give wrong Irms and W.
Voltage rangeNext range above the peakPeak of 264 V AC is about 373 V.
Line filter / bandwidthOff / wide for power and PFA filter removes harmonic current and makes PF look better than it is.
Harmonic modePer IEC 61000-4-7 (10 cycles at 50 Hz, 12 at 60 Hz), up to the 40thRequired for IEC 61000-3-2 compliance results.
WiringVoltage at the DUT terminalsAvoids counting cable losses; use the analyzer’s wiring compensation if available.

5. Test Conditions and the PF Curve

  • Input voltage and frequency: 100/115/230/277 V as applicable, at 50 and 60 Hz.
  • Load points: 10, 25, 50, 75, 100 %. Many specs quote PF at full load only, but PF usually falls at light load.
  • Warm-up: until readings are stable.
  • Plot PF vs load for each input voltage. With active PFC, PF is lowest at light load and high line, because the EMI-filter capacitor current becomes a large part of the small input current.
Input stage: Highlight:
Example PF vs load curves of a power supply at two input voltages.

6. Harmonics, THD and IEC 61000-3-2

The current harmonics explain why the PF is low. Measure each odd harmonic up to the 40th, and the total harmonic distortion:

THDi = √(I2² + I3² + … + I40²) / I1

IEC 61000-3-2 limits harmonic currents of equipment up to 16 A per phase, in four classes:

ClassEquipmentLimits
ABalanced three-phase, household appliances, most othersAbsolute values in A
BPortable tools, non-professional arc weldersClass A × 1.5
CLighting equipment% of fundamental (with special rules for low power)
DPCs, monitors, TVs from 75 W to 600 WmA per watt, capped at Class A values
Input stage: Power:
Each bar is a harmonic current as a percentage of its Class D limit at 230 V (illustrative spectra). Always use the current edition of the standard for compliance.

7. Measurement Errors to Avoid

Method:
The same rectifier load measured four ways. The true PF is 0.57.
  • Distorted source voltage: a flat-topped mains voltage changes the rectifier current and the PF. Use a clean source and record its THD.
  • Source impedance: a weak source or long cables round off the current peaks and make PF look better.
  • Low-bandwidth current sensors: a clamp with a few kHz of bandwidth loses the higher harmonics.
  • Light load: currents are small; use the lowest current range that does not clip.

8. Step-by-Step Procedure and Report

  1. Connect the AC source → power analyzer → DUT → electronic load. Voltage sensed at the DUT terminals.
  2. Set sync to the voltage channel, whole-cycle averaging, voltage and current ranges with crest factor ≥ 3, line filter off.
  3. Set nominal input and full load; warm up until stable.
  4. Record Vrms, Irms, P, S, PF, cos φ, THDi and the source voltage THD.
  5. Repeat at each load point and each input voltage and frequency.
  6. In harmonic mode (IEC 61000-4-7), record the harmonic currents and compare with the applicable IEC 61000-3-2 class.
  7. Plot PF and THD vs load. Report the conditions, instrument and settings, and PASS/FAIL against your PF and harmonic requirements.

9. Common Mistakes and Fixes

MistakeResultFix
Reporting cos φ as PFLooks near 1 for a rectifierPF = W / VA
V × I from two metersOnly VA, no PFPower analyzer for W
Average-responding meterWrong Irms, PF can exceed 1True-RMS analyzer inputs
Partial-cycle windowBiased, jumping readingsSync, whole cycles
Current range clippedLow Irms and WRange with crest factor ≥ 3
Line filter onPF looks better than realFilter off for power readings
Only full load testedLight-load PF missedMeasure the PF curve
Distorted or weak sourceWrong PF and harmonicsClean, stiff source; record its THD

10. Power Factor Calculator

Calculate PF from your readings, split it into displacement and distortion, or list the Class D harmonic limits for your input power.

Power Factor Calculator
Calculate PF from your readings, split it into displacement and distortion, or list the IEC 61000-3-2 Class D harmonic limits for your power.

Related Guides

11. FAQ

How do you measure power factor correctly?
Use a power analyzer that measures real power in watts and apparent power in volt-amperes with true-RMS inputs. Synchronize it to the line voltage, average over whole line cycles, choose ranges with a crest factor of at least 3, keep the line filter off, and divide watts by volt-amperes.
Is cos phi the same as power factor?
Only for pure sine-wave currents. Cos phi measures the phase shift of the fundamental. True power factor also includes distortion: PF = cos phi times the distortion factor. A rectifier without PFC can have cos phi near 1 but a power factor of about 0.5 to 0.7.
Can I measure power factor with a multimeter or clamp meter?
Two meters only give apparent power (V times I), not real power, so they cannot give the power factor. Average-responding meters also misread the peaky current of rectifiers. Some clamp power meters do measure watts and PF, but check their bandwidth and crest factor.
What is the relationship between THD and power factor?
For a sinusoidal voltage, PF = cos phi divided by the square root of 1 plus THD squared, where THD is the current total harmonic distortion as a fraction. For example, 100 % THD with cos phi of 1 gives a PF of about 0.71.
Why is power factor lower at light load?
With active PFC, the EMI filter capacitors draw a leading current that does not change with load. At light load it is a large part of the small input current, so the PF drops, especially at high line voltage.
What are the IEC 61000-3-2 Class D limits?
Class D covers PCs, monitors and TVs from 75 W to 600 W. The limits are 3.4, 1.9, 1.0, 0.5 and 0.35 mA per watt for the 3rd to 11th harmonics and 3.85/n mA per watt for the 13th to 39th, capped at the Class A values. Always check the current edition of the standard.
What crest factor setting do I need?
Capacitor-input rectifier current typically has a crest factor around 3 or more. Choose a current range where the peak stays within the analyzer’s rated crest factor, otherwise the peaks are clipped and Irms and watts are wrong.
Does the AC source affect power factor measurements?
Yes. A distorted (flat-topped) voltage or a weak, high-impedance source changes the current waveform. Use a stiff, low-distortion source, and record the voltage THD with your results.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

electronics believer